| Author |
 Topic  |
|
| |
Current Topic Rating:  | Join the Forum to Rate this Topic at: www.VNCommodore.com Support Forums
|
|
|
madvncom
P Plater
53 Posts
 |
 Posted - 18 Mar 2007 : 1:00:53 PM
|
|
my auto has loose trans selector how do ya go bout fixn it??
|
|
Report to Moderator |
|
|
SWEET
Fully Licenced
600 Posts
 |
Posted - 18 Mar 2007 : 4:27:17 PM
|
| check ur fluid levels, change ur filter n gasket or last of all buy a new trans |
Report to Moderator  |
|
|
madvncom
P Plater
53 Posts
|
|
|
Butcha
P Plater
55 Posts
|
Posted - 19 Mar 2007 : 2:26:51 PM
|
| thats the same thing as my brothers old vn, i just simply suggest a new gearbox much better than stuffing around with oils |
VN COMMODORES JUST HAPPEN TO BE THE BEST CARS EVER |
| Report to Moderator |
|
|
trizo
Forum Moderator
3091 Posts
|
Posted - 19 Mar 2007 : 6:41:48 PM
|
| try reseting your kik bak cable!!!! |
3 can keep a secret if 2 are dead |
| Report to Moderator |
|
|
mouce
National Driver
1525 Posts
|
Posted - 26 Mar 2007 : 9:27:12 PM
|
When you say the tranny selector is loose, do you mean the handle is physically loose, or the shaft or just the thing that lists PRNDD21?
If it's the handle, just nip up the screws.
If it's the shaft...try to work out what has snapped or is about to snap and pray you can get it to the garage before it does let go.
If it's just the surround, pop the cover off and re-align it, a couple of bits of blu-tak will hold it in place nicely.
If the selector is okay, but the shifts are sloppy as hell...a fluid change MAY help, a fully tranny service would be a better option (and cheaper than replacing the tranny). |
Bite off more than you can chew, and chew like hell - Peter Brock (1945-2006) |
| Report to Moderator |
|
|
madvncom
P Plater
53 Posts
|
Posted - 31 May 2007 : 2:08:36 PM
|
| thanx for ya help again mouce as i said i am still learning the vn |
| Report to Moderator |
|
|
trizo
Forum Moderator
3091 Posts
|
Posted - 31 May 2007 : 6:49:43 PM
|
| lo mouce were the bloody hell r ya?? |
3 can keep a secret if 2 are dead |
| Report to Moderator |
|
|
madvncom
P Plater
53 Posts
|
Posted - 03 Jun 2007 : 4:21:04 PM
|
| it seems to be loose in the handle but the screws are done up tight so where should i look at next because there is to much free play when ya move the handle,thanx for ya help |
| Report to Moderator |
|
|
nodg
National Driver
1667 Posts
|
Posted - 03 Jun 2007 : 4:45:16 PM
|
| if a gear shifter in a vn is loose, superglue it. my mate complained about this a few months ago and the only option was to superglue it for the fact that it gets loose like a prostitutes va*ina when played with to much or reefed on. can you get a pic? |
Cheers,
Nodg. |
| Report to Moderator |
|
|
nodg
National Driver
1667 Posts
|
Posted - 03 Jun 2007 : 4:47:08 PM
|
| you are talking about the trim on top of the shifter? |
Cheers,
Nodg. |
| Report to Moderator |
|
|
madvncom
P Plater
53 Posts
|
Posted - 04 Jun 2007 : 12:04:55 PM
|
| nah the handle itself is loose when ya select gears |
| Report to Moderator |
|
|
trizo
Forum Moderator
3091 Posts
|
Posted - 04 Jun 2007 : 12:08:26 PM
|
| swap the whole shifter over m8! |
3 can keep a secret if 2 are dead |
| Report to Moderator |
|
|
nodg
National Driver
1667 Posts
|
|
|
madvncom
P Plater
53 Posts
|
Posted - 05 Jun 2007 : 3:12:21 PM
|
so what do ya do about worn bushes nodq sorry for sounding dumb m8
|
| Report to Moderator |
|
|
nodg
National Driver
1667 Posts
|
Posted - 06 Jun 2007 : 08:56:21 AM
|
| go to your mechanic down the road and give him 50 bucks. unless you have lots of paitents. |
Cheers,
Nodg. |
| Report to Moderator |
|
|
trizo
Forum Moderator
3091 Posts
|
Posted - 06 Jun 2007 : 6:35:51 PM
|
| Still think it would b easier and (cheaper) to replace the shifter with a good 2nd hand from the wreckers! |
3 can keep a secret if 2 are dead |
| Report to Moderator |
|
|
madvncom
P Plater
53 Posts
|
Posted - 30 Jun 2007 : 1:00:38 PM
|
| i asked one of the trans places where i live they quoted me $160.00 is that good or bad cause i think it's a bit steep but i don't know? |
| Report to Moderator |
|
|
trizo
Forum Moderator
3091 Posts
|
Posted - 30 Jun 2007 : 1:06:34 PM
|
what was that quote 4??
|
3 can keep a secret if 2 are dead |
| Report to Moderator |
|
|
madvncom
P Plater
53 Posts
|
|
|
trizo
Forum Moderator
3091 Posts
|
Posted - 30 Jun 2007 : 2:39:50 PM
|
| yep thats good m8! |
3 can keep a secret if 2 are dead |
| Report to Moderator |
|
|
VNSVLE
Forum Moderator
1316 Posts
|
Posted - 30 Jun 2007 : 3:24:48 PM
|
| Depends if you want to do it yourself a transmission service should cost as little as $50 to get the oil, filter and new sump gasket. |
What's the difference between understeer and oversteer?
Understeer is when the driver is scared.
Oversteer is when the passenger is scared. |
| Report to Moderator |
|
|
trizo
Forum Moderator
3091 Posts
|
Posted - 30 Jun 2007 : 3:27:51 PM
|
| gota have a basic knowlage of gearbox's though!!! |
3 can keep a secret if 2 are dead |
| Report to Moderator |
|
| |
Topic |
|
Topic Locked
